C18

Bore
5.7 in / 145 mm
Stroke
7.2 in / 183 mm
Height
94.8 in / 2408 mm

The C18 is the latest generator and brings commonality with our petroleum products as well as interfacing improvements. We have also taken this opportunity to add new price list options. All engine ratings and emissions certifications are the same, however we have been able to increase the power output of the generator for 12 of the 14 ratings.

Power Rating
Power Range 260 - 565 ekW
Generator Set Specifications
Frequency 50 / 60
Minimum Rating 260 ekW (325 kVA)
Maximum Rating 565 ekW (706 kVA)
Engine Specifications
Configuration In-line 6, 4-Stroke-Cycle Diesel
Aspiration Turbocharged - Aftercooled
Bore 5.7 in / 145 mm
Stroke 7.2 in / 183 mm
Fuel System MEUI
Oil Change Interval 250 / 500 hours
Governor Electronic
Refill Capacity 68
Cooling Heat Exchanger, Keel, Radiator Cooled
Rotation from Flywheel End SAE No. (136 teeth)
Generator Set Configurations
Emissions EPA Tier 3, IMO II, EU IWW, EU Stage V, China II
Generator Set Dimensions - Radiator Cooled
Height 94.8 in / 2408 mm
Length 55.6 in / 4741 mm
Width 66.9 in / 1699 mm
Weight - Approximate 13396 lb / 6076 kg
Generator Set Dimensions - Keel and Hex Cooled
Length 119.6 in / 3038 mm
Height 64.9 in / 1648 mm
Width 55.6 in / 1411 mm
Weight - Approximate 9747 lb / 4221 kg
Generator Specifications
Excitation SRMP
Insulation Class H
IP Rating IP23 (standard), IP 44 (optional)
Voltage Regulator CDVR (Digital Voltage)

Standard Equipment

  • Air inlet system
    • Separate circuit after-cooled (SCAC)
    • Open Crankcase Ventilation (OCV) system
  • Turbocharger, jacket water cooled
  • Turbocharger inlet, 152 mm (6 in) OD straight connection
  • Cooling system
    • SCAC pump, gear driven, for HEX cooled engines only
    • Jacket water pump, gear driven
    • SCAC and JW shunt tanks for maintaining proper pump inlet pressures
  • Exhaust system
    • Water-cooled exhaust manifold & turbocharger
    • Round flanged exhaust outlet
  • Fuel system
    • Hybrid fuel line design
    • Fuel transfer pump, gear driven
    • Front service simplex fuel system
    • Manual fuel priming pump
  • Lube system
    • Center sump oil pan: Deep 500 hour oil change interval
    • Front and top service oil filler locations
    • Front service dipstick
  • Oil pump, gear driven
  • Mounting system
    • Vibration Isolators
    • Formed C-channel rails
  • Control system
    • Common Interface to all Genset Control Panels
    • Programmable Low Idle
    • Electronic Diagnostics and Fault Logging
    • Electronic Fuel/Air Ratio Control
  • Programmable ECM Shutdowns for: High Jacket Water Coolant Temp Low Engine Oil Pressure Engine Overspeed

Optional Equipment

  • Exhaust system
    • Dry Elbows
    • Water-Cooled Elbows
    • Flexible Fitting
    • Flange
    • Muffler
    • Muffler, Spark Arresting
  • Air inlet system
    • Air Inlet Adapter
  • Charging system
    • Battery Chargers 10 amp
    • Charging alternator 24V 105 amp
  • Control system
    • Caterpillar alarm and protection
    • EMCP 4.2 control panel
    • MGCP III B control panel
  • Fuel system
    • Duplex fuel filter – front service
    • Fuel cooler
    • Primary fuel/water separator
  • Instrumentation
    • Generator service side - LH, RH
    • Generator terminal box extension
    • Load sharing module (option for type approved module)
  • Lube system
    • Duplex oil filter
    • Sump pump
  • Protection system
    • Generator protection - IP44
  • Starting system
    • Starting motors - electric and/or air
    • Jacket water heaters
Contact Us
x

We're here to help

We'll do our best to get back to you as soon as possible.